A new roof for a typical home in Baton Rouge, LA often costs about $8,000 to $18,000, depending on roof size, material, slope, removal requirements, and structural repairs. A straightforward architectural asphalt shingle replacement may fall near the middle of that range, while metal roofing, complex roof designs, or extensive decking damage can raise the total substantially.
Commercial roofing costs vary more widely because building size, roof access, drainage design, insulation, and membrane type all affect the project. A small commercial roof may cost several thousand dollars, while larger buildings can require budgets in the tens or hundreds of thousands.
What is the average cost of a new residential roof?
For a common single-family home with roughly 1,500 to 2,500 square feet of roof area, approximate installed costs are:
- Basic three-tab asphalt shingles: $6,000 to $10,000
- Architectural asphalt shingles: $8,000 to $16,000
- Impact-resistant shingles: $10,000 to $18,000
- Corrugated or exposed-fastener metal roofing: $10,000 to $20,000
- Standing-seam metal roofing: $15,000 to $30,000 or more
These figures generally assume removal of the existing roof, installation of underlayment and new roofing, normal flashing work, disposal, and cleanup. They are planning ranges rather than guaranteed prices.
Roof area is not the same as the homeβs interior floor area. A one-story house with a simple roof may have a roof area close to its footprint, while a home with multiple levels, dormers, valleys, or wide overhangs may have considerably more roofing.
How is roofing priced?
Roofing is often priced by the square, which equals 100 square feet of roof surface. For example, a roof measuring 2,000 square feet contains 20 squares before accounting for waste and cutting.
A typical architectural shingle installation in the area may range from approximately $350 to $650 per square, while standing-seam metal can exceed $850 to $1,500 per square. The price per square usually includes more than the visible roofing material. Labor, tear-off, underlayment, flashing, ventilation, fasteners, equipment, and disposal are all part of the installed cost.
A low price per square does not necessarily represent a lower total price. A complicated roof may require more labor even if its measured area is relatively small.
Which factors increase the cost?
The largest cost differences usually come from the condition and design of the roof rather than the shingles alone.
Roof pitch and layout
Steep roofs take longer to access and require additional fall-protection measures. Roofs with several valleys, hips, ridges, skylights, chimneys, or attached additions also require more cutting and flashing.
A simple single-ridge roof is usually less expensive than a roof with multiple intersecting sections.
Removal of old roofing
Some roofs can receive a new layer over an existing layer, subject to applicable code and installation requirements. A complete tear-off usually costs more because workers must remove, load, and dispose of the old materials.
Tear-off is often preferred when the existing roof is worn, uneven, saturated, or already has multiple layers. It allows the underlying decking and flashing to be inspected.
Damaged decking
Roof decking is the structural sheathing beneath the underlayment and shingles. Water intrusion, long-term humidity, poor attic ventilation, and repeated leaks can weaken plywood or other sheathing.
Replacement of damaged decking is commonly charged by the sheet or by the affected area. Because the condition is not always visible before removal, a written proposal should explain how concealed damage will be handled.
Flashing, ventilation, and drainage
Roof edges, wall intersections, chimneys, plumbing penetrations, and valleys depend on properly installed flashing. Reusing deteriorated flashing can shorten the life of a new roof.
In the warm, humid climate of Baton Rouge, attic ventilation and moisture control also deserve attention. Poor ventilation does not usually create a line item as large as the roofing material, but it can contribute to premature aging, condensation, and elevated attic temperatures.
How much does a commercial roof replacement cost?
Commercial roofs are commonly priced by square foot, but the range is broad. A basic low-slope membrane replacement may cost roughly $5 to $12 per square foot, while more complex work involving insulation replacement, tapered drainage systems, structural repairs, multiple penetrations, or difficult access may cost more.
Common commercial systems include:
- TPO or PVC membrane
- EPDM rubber membrane
- Modified bitumen
- Built-up roofing
- Metal panels
- Coatings over an existing roof

A 10,000-square-foot commercial roof could therefore range from approximately $50,000 to more than $120,000, depending on the system and existing conditions. That estimate should not be applied to every building. A roof with saturated insulation or inadequate drainage can require substantial additional work.
Commercial buildings also tend to have more rooftop equipment, drains, curbs, vents, and penetrations than houses. Each penetration must be detailed correctly to reduce the risk of future leaks.
Does Baton Rouge weather affect roofing cost?
Yes. Heat, humidity, heavy rainfall, wind, and occasional severe storms influence both material selection and installation planning. High temperatures can make roof work more physically demanding, while rain can interrupt tear-off and expose the building temporarily if the roof is not protected properly.
Storm-related demand can also affect scheduling and pricing after widespread wind or hail events. A roof replacement performed under normal conditions may be easier to plan than emergency work after a major storm.
Algae-resistant shingles may be worth considering in a humid climate because dark streaking is common on shaded or damp roof surfaces. This feature does not make a roof maintenance-free, but it may improve appearance over time.
What should a roofing proposal include?
A useful written proposal should identify the actual scope of work instead of listing only a total price. Look for clear information about:
- Roof material, product line, color, and installation method
- Number of existing layers to be removed
- Underlayment, starter materials, ridge caps, and ventilation
- Flashing replacement or reuse
- Decking repair prices and limits
- Permit responsibilities and disposal
- Cleanup, magnetic nail collection, and protection of landscaping
- Workmanship coverage and manufacturer requirements
- Payment schedule and procedures for concealed conditions
The lowest proposal may exclude items that another proposal includes. Comparing the scope line by line is more useful than comparing totals alone.
Can insurance pay for a new roof?
Insurance generally addresses covered sudden damage, such as certain wind or hail losses, rather than ordinary aging, poor maintenance, or wear. Coverage depends on the policy, deductible, exclusions, date of loss, and the condition of the roof before the event.
A homeowner should document storm damage with photographs and keep records of repairs and maintenance. Filing a claim for normal deterioration may not be appropriate, and accepting a settlement before understanding the repair scope can create confusion.
When is a repair more sensible than replacement?
A repair may be reasonable when the damage is isolated, the roof is relatively young, and the surrounding materials remain serviceable. Replacement becomes more likely when leaks are widespread, shingles are brittle or missing, the roof has reached the end of its expected service life, or the decking and flashing have recurring problems.
Safety and code compliance should guide decisions involving structural sagging, active water entry, exposed electrical components, or steep and damaged roof surfaces. These conditions can make inspection and repair hazardous without appropriate equipment and training.